Brocade 10G-SFPP-LRM Compatible 10.3125G SFP+ 10GBASE-LRM Transceiver Module
Built for hosts recognizing 10G-SFPP-LRM, this HT-manufactured SFP+ module delivers 10.3125G transmission at 1310nm. Its rated reach is 220m on OM3 / 300m on SMF, with Duplex LC as the physical interface. The specifications and engineering guidance below support project teams keep OEM references, delivery records and port schedules aligned, while keeping HT manufacture separate from the OEM cross-reference.
OEM Part Number: 10G-SFPP-LRMHT Part Number: SFP-10GLRM-31
Product Highlights
- Compatible alternative to Brocade 10G-SFPP-LRM
- 10.3125G connectivity at 10.3125Gbps
- Optical wavelength: 1310nm
- Specified reach: 220m on OM3 / 300m on SMF
- Duplex LC / MMF/SMF interface
- Operating temperature: 0 to 70°C (32 to 158°F)
- Factory compatibility verification and optical performance testing before shipment
Specifications
| Brocade Compatible | 10G-SFPP-LRM |
|---|---|
| Manufacturer | HT |
| HT Part Number | SFP-10GLRM-31 |
| Form Factor | SFP+ |
| Max. Data Rate | 10.3125Gbps |
| Wavelength | 1310nm |
| Max. Transmission Distance | 220m@OM3/300m@SMF |
| Connector | Duplex LC |
| Transmitter Type | FP 1310nm |
| Media | MMF/SMF |
| DOM Support | Yes |
| TX Power | -6.5~0.5dBm |
| Receiver Sensitivity | < -8.4dBm |
| Max. Power Consumption | ≤1W |
| Receiver Overload | +1.5dBm |
| Core Size | 50/125µm@OM3 MMF, 9/125μm@SMF |
| Modulation | NRZ |
| Operating Temperature | 0 to 70°C (32 to 158°F) |
| Bit Error Ratio (BER) | 1E-12 |
| Protocols | IEEE 802.3ae, SFF-8472, SFF-8431, SFF-8432, SFP+ MSA Compliant, CPRI, eCPRI |
Project Documentation and Traceability
Large deployments are easier to audit when the order code, optical standard and endpoint record agree. Keep the OEM reference in the compatibility document and the HT part number on the packing list. Labels and carton groups can be arranged by rack or port plan so installers need not identify modules by appearance. For this model, the principal parameters are data rate 10.3125Gbps, wavelength 1310nm, rated reach 220m on OM3 / 300m on SMF.
Brocade Compatibility and Factory Testing
Factory verification starts with the expected 10G-SFPP-LRM identity and finishes with an operating host link. EEPROM data, diagnostic visibility and the stated optical parameters are assessed together. Equipment model, hardware revision and software release can be reviewed before dispatch where platform behavior is uncertain.
Applications and Optical Link Design
Typical deployments include switch-to-switch, switch-to-server and aggregation links inside a data hall or between adjacent equipment rooms. The Duplex LC interface connects to the specified multimode cabling, and the stated reach depends on fiber grade and link loss. Keep this interface on the matching multimode optical standard rather than connecting it directly to a single-mode wavelength or reach variant.
Before deployment, check the host port type, supported data rate and firmware requirements. The 10.3125G interface configuration must match the remote equipment; sharing a SFP+ housing alone does not make two transceiver types interoperable.
For this multimode module, confirm fiber grade, modal bandwidth and total loss before commissioning. The 220m on OM3 / 300m on SMF figure applies only under suitable cabling conditions. Inspect every Duplex LC mating point and match the remote optical standard.
Optical Acceptance, Diagnostics and Handling
For this model, the specified transmit-power range is -6.5~0.5dBm; receiver sensitivity is < -8.4dBm. During commissioning, record the host diagnostic readings after the link has stabilized and compare them with those limits. DOM values are useful operational indicators, but they do not replace calibrated optical measurements when a link is marginal. Investigate unexpected loss through connector inspection, cleaning and a channel measurement before replacing the module. Before every insertion, keep dust caps in place until the patch lead is ready, avoid touching the optical end face and use an appropriate inspection and cleaning procedure. Do not look into an active optical interface.
Frequently Asked Questions
Is this an original Brocade transceiver?
No. It is an HT-manufactured compatible alternative for equipment that specifies 10G-SFPP-LRM, not an original Brocade-branded module.
Which fiber and connector are required?
Use Duplex LC with MMF/SMF. The specified maximum reach is 220m on OM3 / 300m on SMF, subject to fiber quality and total link loss.
Can it be mixed with another wavelength or reach version?
Only when the two ends share the same optical standard, wavelength plan and supported data rate. Check the exact part numbers and link budget rather than relying only on the module form factor.
Ordering Information
Quote HT part number SFP-10GLRM-31 together with OEM reference 10G-SFPP-LRM and quantity. Add the host model and software release when pre-order verification is required. Neutral labels, customer packaging and project-specific compatibility review are available on request.
Shipping and Lead Time
Standard configurations normally ship within one to three working days, with production lead times confirmed for larger quantities. International courier, air freight and sea freight are available; customer courier accounts and nominated forwarders are accepted.
Quality Assurance and Packaging
Before packing, the module receives interface inspection, identification and link checks. Protective packaging avoids pressure on the connector and latch. Customer references, rack groups and project packing lists can be added for volume orders.
