MMC-24 APC to 3 x MTP-8 APC Breakout Cable, 24 Fibers, OM4
For Pakistani procurement and engineering teams, the specification provides a practical basis for checking compatibility before production is requested. The APC-to-APC model of the 24FMMCMTPOM4 breakout carries 24 OM4 fibers from one MMC APC female connector to three MTP-8 APC Elite female legs. All interface points use APC polish, and this breakout body follows factory harness polarity. It includes three eight-fiber multimode routes in one compact, factory-prepared unit.
Product Highlights
- MMC Female to MTP® Female, 24 Fibers
- OM4 50/125μm, bend-insensitive fiber
- MMC insertion loss ≤0.35dB, return loss ≥40/45dB (MMC/MTP®)
- Harness Polarity wiring scheme
- 2.5mm Plenum (OFNP) cable
- Standard length options: 1m (3ft), 2m (7ft), 3m (10ft)
Specifications
| Part Number | 24FMMCMTPOM4 |
|---|---|
| Manufacturer | HT |
| Connector A | US Conec MMC Female (Non-Pinned) |
| Connector B | US Conec MTP® Elite Female (Non-Pinned) |
| Polish Type | APC to APC |
| Glass Fiber | Bend Insensitive Fiber |
| Fiber Mode | OM4 50/125μm |
| Wavelength | 850/1300nm |
| Fiber Count | 24 Fibers |
| Polarity | Harness Polarity |
| Cable Outside Diameter (OD) | 2.5mm |
| Cable Jacket | Plenum (OFNP) |
| Min. Bend Radius (Optical Fiber) | 7.5mm |
| Min. Bend Radius (Fiber Cable) | 20/10D (Dynamic/Static) |
| Tensile Strength (Long Term) | 30N |
| Tensile Strength (Short Term) | 100N |
| Insertion Loss | ≤0.35dB |
| Return Loss | ≥40/45dB (MMC/MTP®) |
| Attenuation at 850nm | ≤2.3dB/km |
| Attenuation at 1300nm | ≤0.6dB/km |
| Operating Temperature | -10 to 60°C (14 to 140℉) |
| Storage Temperature | -10 to 70°C (14 to 158℉) |
A three-way fan-out with uniform polish
The completed cable is suitable when the two the MMC infrastructure and all three MTP destinations are created for APC. Because the optical interfaces are female and non-pinned, pinned mates are project-specific throughout. Before installation, review that the application truly calls for three eight-fiber branches and that no supplementary polarity reversal is introduced by the connected trunk or cassette.
Loss values for the complete optical path
The terminated assembly is rated at 0.35dB maximum insertion loss, with at least 40dB return loss at MMC and 45dB at MTP APC. Use these connector-specific specifications when reviewing the passive connection. OM4 behavior at 850/1300nm supports multimode systems, but allowable distance and aggregate interface count remain properties of the entire transceiver link.
Installing and identifying three APC branches
Catalogue lengths are 1m (3ft), 2m (7ft) and 3m (10ft), with special lengths in feet or meters. Because three comparable MTP connectors leave one fan-out, branch identifiers are in particular valuable. Maintain gentle routing around the breakout body, examine each ferrule and cap any branch that is not to be considered connected immediately.
Ordering and Factory Support
Indicate 24FMMCMTPOM4 in the APC-to-APC three-leg setup, with length and number of units. If the three branches terminate in distinct rack locations, include the project-specific leg arrangement and identification rather than relying on a general-purpose fan-out diagram. For Pakistan, a clear port or maintenance schedule helps us confirm the correct factory-built configuration before supply.
