MTP-8 to MTP-8 UPC Jumper, 8 Fibers, OM4, Type B, 3m (10ft)
A ready to install MTP® Elite Female jumper: 8 Fibers, OM4 50/125μm, Plenum (OFNP). Pre-termination means no polishing, no epoxy and no curing time on site - just route the cable, plug in both ends and bring the link up.
Standard lengths are 1m (3ft), 3m (10ft), 5m (16ft), 7m (23ft), 10m (33ft), 15m (49ft), 20m (66ft), 25m (82ft), 30m (98ft) and 40m (131ft). Because we are the manufacturer, any other length between or beyond these steps can be produced on request, with your choice of jacket color, labeling and packaging.
Product Highlights
- MTP® Elite Female (Non-Pinned) to MTP® Elite Female (Non-Pinned), 8 Fibers
- OM4 50/125μm, bend insensitive fiber
- Insertion loss ≤0.25dB, return loss ≥20dB
- Type B polarity
- 3.0mm Plenum (OFNP) round cable
- Minimum bend radius 7.5mm
- Ten standard lengths from 1m (3ft) to 40m (131ft), custom lengths built to order
Specifications
| Part Number | 8FMTPOM4-3M |
|---|---|
| Manufacturer | HT |
| Connector A | US Conec MTP® Elite Female (Non-Pinned) |
| Connector B | US Conec MTP® Elite Female (Non-Pinned) |
| Fiber Mode | OM4 50/125μm |
| Wavelength | 850/1300nm |
| Polish Type | UPC to UPC |
| Polarity | Type B |
| Cable Jacket | Plenum (OFNP) |
| Fiber Count | 8 Fibers |
| Glass Fiber | Bend Insensitive Fiber |
| Cable Outside Diameter (OD) | 3.0mm |
| Min. Bend Radius (Optical Fiber) | 7.5mm |
| Min. Bend Radius (Fiber Cable) | 20/10D (Dynamic/Static) |
| Connector Durability | 500 times |
| Tensile Strength | 90/180N (Long/Short Term) |
| Insertion Loss | ≤0.25dB |
| Return Loss | ≥20dB |
| Attenuation at 850nm | ≤2.3dB/km |
| Attenuation at 1300nm | ≤0.6dB/km |
| Operating Temperature | -10 to 60°C (14 to 140℉) |
| Storage Temperature | -10 to 70°C (14 to 158℉) |
Applications
Use this jumper anywhere a short multi-fiber connection is needed: panel to equipment, cassette to cassette, or switch to switch within a row. The 8-fiber version matches 400G and 800G parallel interfaces that run on 4 or 8 lanes, such as QSFP112, OSFP and twin-port OSFP connections. Because it arrives polished and tested, the installer only needs to route and connect it.
Polarity and Gender Options
The same jumper can be produced with different polarity and gender combinations. Male connectors carry guide pins for direct module connection, while female versions are used at panels. Polarity A, B and C are all standard for us, and our engineers can check your link diagram if you are unsure which one to order.
Ordering Information
Ordering is simple: send us 8FMTPOM4-3M and your required lengths and quantities, and we return a factory quote the same working day. The 1m (3ft) version is the standard model; Small trial orders are welcome before you commit to a full project rollout.
Quality and Testing
Our test routine covers insertion loss, return loss and ferrule end face inspection on every assembly. Because testing is done in-house, custom variants receive exactly the same verification as standard models.
How We Pack
Every cable is protected with dust caps and individual packaging before being boxed for shipment. Batch test reports and your own part number labels can be included in each bag.
Built to Your Spec
Our engineering team handles custom MPO/MTP assemblies daily. If the standard configuration does not match your link design, send us the requirement and we will build exactly what your network needs at factory-direct cost.
