Juniper Networks JNP-100G-AOCBO Compatible 100G QSFP28 4 x 25G NRZ to 4 x 25G SFP28 NRZ Active Optical Breakout Cable
A 100G direct-attached link depends on the correct host identity, interface mode and physical length. This page covers the Juniper Networks JNP-100G-AOCBO compatible AOC series in QSFP28 to 4x SFP28, including 1m (3ft), 2m (7ft), 3m (10ft), 5m (16ft), 7m (23ft), 10m (33ft), 15m (49ft), 20m (66ft), 25m (82ft), 30m (98ft) and 50m (164ft). Each documented length-specific OEM reference is linked separately where an individual product page is available.
Series Part Number: JNP-100G-AOCBOHT Part Number: JNP-100G-AOCBO
Product Highlights
- HT-manufactured compatible alternative for Juniper Networks JNP-100G-AOCBO
- 100G aggregate connectivity at 100Gbps
- Interface configuration: QSFP28 to 4x SFP28
- Breakout AOC
- Length configurations covered: 1m (3ft), 2m (7ft), 3m (10ft), 5m (16ft), 7m (23ft), 10m (33ft), 15m (49ft), 20m (66ft), 25m (82ft), 30m (98ft) and 50m (164ft)
- Power consumption: 2.2W (QSFP28 End)0.8W (SFP28 Per End)
- Operating temperature: 0 to 70°C (32 to 158°F)
Available Lengths and Corresponding Part Numbers
The documented configurations are 1m (3ft), 2m (7ft), 3m (10ft), 5m (16ft), 7m (23ft), 10m (33ft), 15m (49ft), 20m (66ft), 25m (82ft), 30m (98ft) and 50m (164ft). Each link below opens the separate product page for that physical length and its corresponding OEM part number. Select the exact assembly required by the route and purchase order; custom project lengths can be discussed separately.
Compatible OEM Part Numbers
- JNP-100G-AOCBO-1M
- JNP-100G-AOCBO-2M
- JNP-100G-AOCBO-3M
- JNP-100G-AOCBO-5M
- JNP-100G-AOCBO-7M
- JNP-100G-AOCBO-10M
- JNP-100G-AOCBO-15M
- JNP-100G-AOCBO-20M
- JNP-100G-AOCBO-25M
- JNP-100G-AOCBO-30M
- JNP-100G-AOCBO-50M
Specifications
| Juniper Networks Compatible | JNP-100G-AOCBO-1M |
|---|---|
| Manufacturer | HT |
| HT Part Number | JNP-100G-AOCBO |
| Form Factor | QSFP28 to 4x SFP28 |
| Max. Data Rate | 100Gbps |
| Cable Length Options Covered | 1m (3ft), 2m (7ft), 3m (10ft), 5m (16ft), 7m (23ft), 10m (33ft), 15m (49ft), 20m (66ft), 25m (82ft), 30m (98ft) and 50m (164ft) |
| Cable Type | Breakout AOC |
| Wavelength | 850nm |
| Minimum Bend Radius | 30mm |
| Transmitter Type | VCSEL |
| Receiver Type | PIN |
| Max. Power Consumption | 2.2W (QSFP28 End)0.8W (SFP28 Per End) |
| Modulation Format | QSFP28-4x 25G-NRZ SFP28-1x 25G-NRZ |
| CDR (Clock and Data Recovery) | TX & RX Built-in CDR |
| Jacket Material | OFNP |
| DDM/DOM | Supported |
| Commercial Temperature Range | 0 to 70°C (32 to 158°F) |
| Protocols | QSFP28 MSA, SFP28 MSA |
Project Documentation and Cable Identification
Large deployments are easier to audit when the order code, physical length and endpoint record agree. Keep the OEM reference in the compatibility document and use the HT part number on the packing list. Where several lengths arrive together, labels and carton groups can be arranged by rack or port plan so installers do not have to identify cables by appearance alone. For this series, keep the interface rate, AOC construction and length-specific OEM reference together throughout that review.
Juniper Networks Compatibility and Factory Testing
Factory verification links the compatibility identity to the exact physical assembly described on this page. Identification, connector condition and live link behavior are checked before packing. Customers can submit equipment and firmware details with the project documentation for a more specific pre-order compatibility review. Series-level inspection is followed by the exact length and OEM configuration selected for dispatch. Functional verification includes link establishment and diagnostic indications where the host exposes them.
Applications and Deployment
An AOC removes the separate module-and-fiber interfaces from a high-speed connection. Both optical ends remain attached to the cable, simplifying polarity control and connector handling. Host identification, wavelength plan, aggregate rate and any breakout configuration must still agree across the link. For this series, the listed interface is QSFP28 to 4x SFP28 and the aggregate rate is 100G.
Cable Construction and Routing
For this assembly, the jacket material is OFNP; the minimum bend radius is 30mm; the operating temperature is 0 to 70°C (32 to 158°F); the power consumption is 2.2W (QSFP28 End)0.8W (SFP28 Per End). These parameters belong in the installation review rather than being treated as catalogue trivia. Route the cable through its intended managers without tension, avoid pressure close to the connector boots and leave enough space to operate the latches. Any service loop must respect the stated bend limit.
Ordering Information
Use the listed HT part number for ordering and retain the OEM reference as the host-compatibility cross-reference. Send quantities by length, along with any rack-based packing or label instructions. If the project has mixed equipment, include the host model for each group rather than relying only on the aggregate cable rate. For this series, follow the corresponding length link, quote that exact OEM part number and keep different lengths on separate order lines. HT part number JNP-100G-AOCBO identifies the product family; the linked page provides the final length-specific identity.
Shipping and Lead Time
Standard configurations normally ship within one to three working days, with production lead times confirmed for larger quantities. International courier, air freight and sea freight are available; customer courier accounts and nominated forwarders are accepted.
Quality Assurance and Packaging
Inspection and link testing are completed before the cable enters its protective packaging. Project orders can be packed and labelled by length, rack or customer reference, with packing documentation that makes received quantities straightforward to reconcile against the installation schedule. Both connector ends are inspected as part of the complete assembly, and protective packing is selected to avoid tight bends during transport and storage.
Frequently Asked Questions
Is this an original Juniper Networks cable?
No. It is an HT-manufactured compatible cable for equipment that specifies JNP-100G-AOCBO, not an original Juniper Networks-branded product.
Are different lengths and OEM part numbers separate products?
Yes. Where a length has its own OEM reference, follow the corresponding link above and order that exact part number on its own line. Do not substitute another length only because the connector arrangement is the same.
