Juniper Networks OSFP-800G-AOC Compatible 800G OSFP 8 x 100G PAM4 IHS/Finned Top Active Optical Cable
For equipment that specifies Juniper Networks OSFP-800G-AOC, this HT-manufactured AOC family offers 800G direct-attach connectivity with OSFP (IHS/Finned Top) to OSFP (IHS/Finned Top). Rather than treating different OEM length codes as interchangeable, the available configurations below link to their own product pages. Mechanical details, installation planning and factory checks are included for engineering and purchasing review.
Series Part Number: OSFP-800G-AOCHT Part Number: OSFP-800G-AOC
Product Highlights
- HT-manufactured compatible alternative for Juniper Networks OSFP-800G-AOC
- 800G aggregate connectivity at 800Gbps
- Interface configuration: OSFP (IHS/Finned Top) to OSFP (IHS/Finned Top)
- Active Optical Cable
- Length configurations covered: 1m (3ft), 3m (10ft), 5m (16ft), 7m (23ft), 10m (33ft), 15m (49ft), 20m (66ft), 25m (82ft), 30m (98ft) and 50m (164ft)
- Power consumption: 14W Per End
- Operating temperature: 0 to 70°C (32 to 158°F)
Available Lengths and Corresponding Part Numbers
The documented configurations are 1m (3ft), 3m (10ft), 5m (16ft), 7m (23ft), 10m (33ft), 15m (49ft), 20m (66ft), 25m (82ft), 30m (98ft) and 50m (164ft). Each link below opens the separate product page for that physical length and its corresponding OEM part number. Select the exact assembly required by the route and purchase order; custom project lengths can be discussed separately.
Compatible OEM Part Numbers
- OSFP-800G-AOC-1M
- OSFP-800G-AOC-3M
- OSFP-800G-AOC-5M
- OSFP-800G-AOC-7M
- OSFP-800G-AOC-10M
- OSFP-800G-AOC-15M
- OSFP-800G-AOC-20M
- OSFP-800G-AOC-25M
- OSFP-800G-AOC-30M
- OSFP-800G-AOC-50M
Specifications
| Juniper Networks Compatible | OSFP-800G-AOC-1M |
|---|---|
| Manufacturer | HT |
| HT Part Number | OSFP-800G-AOC |
| Form Factor | OSFP (IHS/Finned Top) to OSFP (IHS/Finned Top) |
| Max. Data Rate | 800Gbps |
| Cable Length Options Covered | 1m (3ft), 3m (10ft), 5m (16ft), 7m (23ft), 10m (33ft), 15m (49ft), 20m (66ft), 25m (82ft), 30m (98ft) and 50m (164ft) |
| Cable Type | Active Optical Cable |
| Wavelength | 850nm |
| Minimum Bend Radius | 30mm |
| Transmitter Type | VCSEL |
| Receiver Type | PIN |
| Max. Power Consumption | 14W Per End |
| Modulation Format | 8x 100G-PAM4 |
| CDR (Clock and Data Recovery) | TX & RX Built-in CDR |
| Jacket Material | OFNP |
| DDM/DOM | Supported |
| Commercial Temperature Range | 0 to 70°C (32 to 158°F) |
| Protocols | OSFP MSA, CMIS Rev 4.0, SFF-8679, IEEE 802.3bs |
Project Documentation and Cable Identification
Large deployments are easier to audit when the order code, physical length and endpoint record agree. Keep the OEM reference in the compatibility document and use the HT part number on the packing list. Where several lengths arrive together, labels and carton groups can be arranged by rack or port plan so installers do not have to identify cables by appearance alone. For this series, keep the interface rate, AOC construction and length-specific OEM reference together throughout that review.
Juniper Networks Compatibility and Factory Testing
Factory verification links the compatibility identity to the exact physical assembly described on this page. Identification, connector condition and live link behavior are checked before packing. Customers can submit equipment and firmware details with the project documentation for a more specific pre-order compatibility review. Series-level inspection is followed by the exact length and OEM configuration selected for dispatch. Functional verification includes link establishment and diagnostic indications where the host exposes them.
Applications and Deployment
Active optical cables integrate optical engines and fiber into a single factory-terminated link. They provide a lighter, longer-reach alternative to copper direct attach without requiring separate transceiver and patch-cord selection. The complete assembly should be routed with bend protection and connected only between compatible optical standards and port modes. For this series, the listed interface is OSFP (IHS/Finned Top) to OSFP (IHS/Finned Top) and the aggregate rate is 800G.
Cable Construction and Routing
The specification table records the jacket material is OFNP; the minimum bend radius is 30mm; the operating temperature is 0 to 70°C (32 to 158°F); the power consumption is 14W Per End. Use those values when preparing the rack pathway and receiving checklist. Do not pull a connector by its cable, compress the run under tight ties or force excess length into a sharp coil. Connector protection should remain in place until the assembly is ready for insertion.
Ordering Information
Use the listed HT part number for ordering and retain the OEM reference as the host-compatibility cross-reference. Send quantities by length, along with any rack-based packing or label instructions. If the project has mixed equipment, include the host model for each group rather than relying only on the aggregate cable rate. For this series, follow the corresponding length link, quote that exact OEM part number and keep different lengths on separate order lines. HT part number OSFP-800G-AOC identifies the product family; the linked page provides the final length-specific identity.
Shipping and Lead Time
Standard configurations normally ship within one to three working days, with production lead times confirmed for larger quantities. International courier, air freight and sea freight are available; customer courier accounts and nominated forwarders are accepted.
Quality Assurance and Packaging
Inspection and link testing are completed before the cable enters its protective packaging. Project orders can be packed and labelled by length, rack or customer reference, with packing documentation that makes received quantities straightforward to reconcile against the installation schedule. Both connector ends are inspected as part of the complete assembly, and protective packing is selected to avoid tight bends during transport and storage.
Frequently Asked Questions
Is this an original Juniper Networks cable?
No. It is an HT-manufactured compatible cable for equipment that specifies OSFP-800G-AOC, not an original Juniper Networks-branded product.
Are different lengths and OEM part numbers separate products?
Yes. Where a length has its own OEM reference, follow the corresponding link above and order that exact part number on its own line. Do not substitute another length only because the connector arrangement is the same.
