Cisco OSFP-800G-VR8P Compatible 800G Single-port OSFP IHS/Closed Finned Top SR8 Transceiver Module
Built for hosts recognizing OSFP-800G-VR8P, this HT-manufactured Single-port OSFP IHS/Closed Finned Top module delivers 800G transmission at 850nm. Its rated reach is 60m on OM3 / 100m on OM4, with MTP/MPO-16 APC as the physical interface. The specifications and engineering guidance below support project teams keep OEM references, delivery records and port schedules aligned, while keeping HT manufacture separate from the OEM cross-reference.
OEM Part Number: OSFP-800G-VR8PHT Part Number: OSFP-SR8-800G
Product Highlights
- Compatible alternative to Cisco OSFP-800G-VR8P
- 800G connectivity at 850Gbps (8x 106.25Gbps)
- Optical wavelength: 850nm
- Specified reach: 60m on OM3 / 100m on OM4
- MTP/MPO-16 APC / MMF interface
- Digital diagnostic monitoring: Supported
- Operating temperature: 0 to 70°C (32 to 158°F)
Specifications
| HT Part Number | OSFP-SR8-800G |
|---|---|
| Manufacturer | HT |
| Form Factor | Single-port OSFP IHS/Closed Finned Top |
| Max. Data Rate | 850Gbps (8x 106.25Gbps) |
| Wavelength | 850nm |
| Max. Cable Distance | 60m@OM3/100m@OM4 |
| Connector | MTP/MPO-16 APC |
| Media | MMF |
| Transmitter Type | VCSEL |
| Receiver Type | PD |
| TX Power | -4.6~4dBm |
| Minimum Receiver Power | -6.4dBm |
| Power Budget | 1.8dB |
| Receiver Overload | 4dBm |
| Max. Power Consumption | 16W |
| Extinction Ratio | ＞2.5dB |
| DDM/DOM | Supported |
| Commercial Temperature Range | 0 to 70°C (32 to 158°F) |
| Modulation (Electrical) | 8x100G-PAM4 |
| Modulation (Optical) | 8x100G-PAM4 |
| CDR (Clock and Data Recovery) | TX & RX Built-in CDR |
| Inbuilt FEC | Yes |
| Protocols | OSFP MSA Rev 5.1, CMIS Rev 5.0, IEEE 802.3df-2024, IEEE 802.3df-2024 |
Project Documentation and Traceability
Large deployments are easier to audit when the order code, optical standard and endpoint record agree. Keep the OEM reference in the compatibility document and the HT part number on the packing list. Labels and carton groups can be arranged by rack or port plan so installers need not identify modules by appearance. For this model, the principal parameters are data rate 850Gbps (8x 106.25Gbps), wavelength 850nm, rated reach 60m on OM3 / 100m on OM4.
Cisco Compatibility and Factory Testing
Factory verification starts with the expected OSFP-800G-VR8P identity and finishes with an operating host link. EEPROM data, diagnostic visibility and the stated optical parameters are assessed together. Equipment model, hardware revision and software release can be reviewed before dispatch where platform behavior is uncertain.
Applications and Optical Link Design
Typical deployments include switch-to-switch, switch-to-server and aggregation links inside a data hall or between adjacent equipment rooms. The MTP/MPO-16 APC interface connects to the specified multimode cabling, and the stated reach depends on fiber grade and link loss. Keep this interface on the matching multimode optical standard rather than connecting it directly to a single-mode wavelength or reach variant.
Before deployment, check the host port type, supported data rate and firmware requirements. The 800G interface configuration must match the remote equipment; sharing a Single-port OSFP IHS/Closed Finned Top housing alone does not make two transceiver types interoperable.
For this multimode module, confirm fiber grade, modal bandwidth and total loss before commissioning. The 60m on OM3 / 100m on OM4 figure applies only under suitable cabling conditions. Inspect every MTP/MPO-16 APC mating point and match the remote optical standard.
Optical Acceptance, Diagnostics and Handling
For this model, the specified transmit-power range is -4.6~4dBm; the stated optical power budget is 1.8dB. During commissioning, record the host diagnostic readings after the link has stabilized and compare them with those limits. DOM values are useful operational indicators, but they do not replace calibrated optical measurements when a link is marginal. Investigate unexpected loss through connector inspection, cleaning and a channel measurement before replacing the module. Diagnostic monitoring is listed as Supported. Before every insertion, keep dust caps in place until the patch lead is ready, avoid touching the optical end face and use an appropriate inspection and cleaning procedure. Do not look into an active optical interface.
Frequently Asked Questions
Is this an original Cisco transceiver?
No. It is an HT-manufactured compatible alternative for equipment that specifies OSFP-800G-VR8P, not an original Cisco-branded module.
Which fiber and connector are required?
Use MTP/MPO-16 APC with MMF. The specified maximum reach is 60m on OM3 / 100m on OM4, subject to fiber quality and total link loss.
Can it be mixed with another wavelength or reach version?
Only when the two ends share the same optical standard, wavelength plan and supported data rate. Check the exact part numbers and link budget rather than relying only on the module form factor.
Ordering Information
Use OSFP-800G-VR8P as the compatibility cross-reference and OSFP-SR8-800G as the HT ordering identity. Keep other reaches or wavelength directions on separate order lines. Neutral labels, customer packaging and project-specific compatibility review are available on request.
Shipping and Lead Time
Standard configurations normally ship within one to three working days, with production lead times confirmed for larger quantities. International courier, air freight and sea freight are available; customer courier accounts and nominated forwarders are accepted.
Quality Assurance and Packaging
Each OSFP-800G-VR8P compatible module is inspected, powered up and functionally checked before protective packing. Dust caps and individual trays shield the interface during transport. Customer references, rack groups and project packing lists can be added for volume orders.
