Generic QDD-200G-8LCAO01-E Compatible 200G QSFP-DD 8 x 25G NRZ to 8 x 25G LC Duplex Active Optical Breakout Cable
For equipment that specifies Generic QDD-200G-8LCAO01-E, this HT-manufactured AOC family offers 200G direct-attach connectivity with direct-attach. Rather than treating different OEM length codes as interchangeable, the available configurations below link to their own product pages. Mechanical details, installation planning and factory checks are included for engineering and purchasing review.
Series Part Number: QDD-200G-8LCAO01-EHT Part Number: QDD-200G-8LCAO01-E
Product Highlights
- HT-manufactured compatible alternative for Generic QDD-200G-8LCAO01-E
- 200G aggregate connectivity at 200Gbps
- Optical Cable
- Length configurations covered: 1m (3ft), 3m (10ft), 5m (16ft), 7m (23ft), 10m (33ft), 15m (49ft), 20m (66ft), 25m (82ft), 30m (98ft), 50m (164ft) and 70m (230ft)
- Power consumption: ≤3.47W
Available Lengths and Corresponding Part Numbers
The documented configurations are 1m (3ft), 3m (10ft), 5m (16ft), 7m (23ft), 10m (33ft), 15m (49ft), 20m (66ft), 25m (82ft), 30m (98ft), 50m (164ft) and 70m (230ft). Each link below opens the separate product page for that physical length and its corresponding OEM part number. Select the exact assembly required by the route and purchase order; custom project lengths can be discussed separately.
Compatible OEM Part Numbers
- QDD-200G-8LCAO01-E-1M3FT
- QDD-200G-8LCAO01-E-3M10FT
- QSFP28-DD to Duplex-LC-200G-AOC-5M16FT
- QSFP28-DD to Duplex-LC-200G-AOC-7M23FT
- QSFP28-DD to Duplex-LC-200G-AOC-10M33FT
- QSFP28-DD to Duplex-LC-200G-AOC-15M49FT
- QSFP28-DD to Duplex-LC-200G-AOC-20M66FT
- QSFP28-DD to Duplex-LC-200G-AOC-25M82FT
- QSFP28-DD to Duplex-LC-200G-AOC-30M98FT
- QSFP28-DD to Duplex-LC-200G-AOC-50M164FT
- QSFP28-DD to Duplex-LC-200G-AOC-70M230FT
- QDD-200G-8LCAO01-E
- QDD-200G-8LCAO03-E
Specifications
| HT Part Number | QDD-200G-8LCAO01-E |
|---|---|
| Manufacturer | HT |
| Connector Type | QSFP28-DD to Duplex-LC |
| Max Data Rate | 200Gbps |
| Minimum Bend Radius | 30mm |
| Cable Length Options Covered | 1m (3ft), 3m (10ft), 5m (16ft), 7m (23ft), 10m (33ft), 15m (49ft), 20m (66ft), 25m (82ft), 30m (98ft), 50m (164ft) and 70m (230ft) |
| Wavelength | 850nm |
| Cable Type | Optical Cable |
| Modulation Format | NRZ |
| Power Consumption | ≤3.47W |
| Power supply | 3.5V |
| Extend Temperature Range | -20°C to +85°C |
| Protocols | QSFP-DD MSA CMIS 4.0, IEEE 802.3bs 200G-SR8, IEEE 802.3by 25G-SR |
| Application | Ethernet, 5G Front Haul |
Project Documentation and Cable Identification
Large deployments are easier to audit when the order code, physical length and endpoint record agree. Keep the OEM reference in the compatibility document and use the HT part number on the packing list. Where several lengths arrive together, labels and carton groups can be arranged by rack or port plan so installers do not have to identify cables by appearance alone. For this series, keep the interface rate, AOC construction and length-specific OEM reference together throughout that review.
Generic Compatibility and Factory Testing
Factory verification links the compatibility identity to the exact physical assembly described on this page. Identification, connector condition and live link behavior are checked before packing. Customers can submit equipment and firmware details with the project documentation for a more specific pre-order compatibility review. Series-level inspection is followed by the exact length and OEM configuration selected for dispatch. Functional verification includes link establishment and diagnostic indications where the host exposes them.
Applications and Deployment
An AOC removes the separate module-and-fiber interfaces from a high-speed connection. Both optical ends remain attached to the cable, simplifying polarity control and connector handling. Host identification, wavelength plan, aggregate rate and any breakout configuration must still agree across the link. For this series, the listed interface is the stated interface and the aggregate rate is 200G. The stated application is Ethernet, 5G Front Haul.
Cable Construction and Routing
The specification table records the minimum bend radius is 30mm; the power consumption is ≤3.47W. Use those values when preparing the rack pathway and receiving checklist. Do not pull a connector by its cable, compress the run under tight ties or force excess length into a sharp coil. Connector protection should remain in place until the assembly is ready for insertion.
Ordering Information
Use the listed HT part number for ordering and retain the OEM reference as the host-compatibility cross-reference. Send quantities by length, along with any rack-based packing or label instructions. If the project has mixed equipment, include the host model for each group rather than relying only on the aggregate cable rate. For this series, follow the corresponding length link, quote that exact OEM part number and keep different lengths on separate order lines. HT part number QDD-200G-8LCAO01-E identifies the product family; the linked page provides the final length-specific identity.
Shipping and Lead Time
Standard configurations normally ship within one to three working days, with production lead times confirmed for larger quantities. International courier, air freight and sea freight are available; customer courier accounts and nominated forwarders are accepted.
Quality Assurance and Packaging
Inspection and link testing are completed before the cable enters its protective packaging. Project orders can be packed and labelled by length, rack or customer reference, with packing documentation that makes received quantities straightforward to reconcile against the installation schedule. Both connector ends are inspected as part of the complete assembly, and protective packing is selected to avoid tight bends during transport and storage.
Frequently Asked Questions
Is this an original Generic cable?
No. It is an HT-manufactured compatible cable for equipment that specifies QDD-200G-8LCAO01-E, not an original Generic-branded product.
Are different lengths and OEM part numbers separate products?
Yes. Where a length has its own OEM reference, follow the corresponding link above and order that exact part number on its own line. Do not substitute another length only because the connector arrangement is the same.
Does this AOC cable require separate modules at each end?
No. The connector ends and cable form one complete direct-attach assembly. The ends are not detachable standalone transceivers, and the complete product is tested together.
What information helps confirm compatibility?
Provide the equipment manufacturer and model, port type, hardware revision and software release, together with the required OEM reference, length and quantity. Breakout projects should also identify the intended lane configuration.
