Juniper Networks QDD-2X400G-FR4-P Compatible 800G QSFP-DD Transceiver Module
Built for hosts recognizing QDD-2X400G-FR4-P, this HT-manufactured QSFP-DD module delivers 800G transmission at 1271nm, 1291nm, 1311nm and 1331nm. Its rated reach is 2km, with Dual Duplex LC/UPC as the physical interface. The specifications and engineering guidance below support project teams keep OEM references, delivery records and port schedules aligned, while keeping HT manufacture separate from the OEM cross-reference.
OEM Part Number: QDD-2X400G-FR4-PHT Part Number: QDD-2FR4-800G
Product Highlights
- Compatible alternative to Juniper Networks QDD-2X400G-FR4-P
- 800G connectivity at 850Gbps (8x 106.25Gbps)
- Optical wavelength: 1271nm, 1291nm, 1311nm and 1331nm
- Specified reach: 2km
- Dual Duplex LC/UPC / SMF interface
- Factory compatibility verification and optical performance testing before shipment
Specifications
| Juniper Networks Compatible | QDD-2X400G-FR4-P |
|---|---|
| Manufacturer | HT |
| HT Part Number | QDD-2FR4-800G |
| Form Factor | QSFP-DD |
| Max Data Rate | 850Gbps (8x 106.25Gbps) |
| Wavelength | 1271nm, 1291nm, 1311nm and 1331nm |
| Max Cable Distance | 2km |
| Connector | Dual Duplex LC/UPC |
| Media | SMF |
| Transmitter Type | EML |
| Receiver Type | PIN |
| TX Power | -3.2~4.4dBm |
| Minimum Receiver Power | -7.2dBm |
| Power Budget | 4dB |
| Receiver Overload | 4.4dBm |
| Max Power Consumption | 17W |
| Extinction Ratio | ≥3.5dB |
| Modulation (Electrical) | 8x100G-PAM4 |
| Modulation (Optical) | 8x100G-PAM4 |
| Packaging Technology | COB (Chip on Board) Packaging |
| CDR (Clock and Data Recovery) | TX and RX Built-in DSP |
| Inbuilt FEC | No |
| Protocols | IEEE 802.3cu-2021, IEEE 802.3ck-2022, QSFP-DD MSA HW Rev 6.01, CMIS Rev 5.0 |
Project Documentation and Traceability
Large deployments are easier to audit when the order code, optical standard and endpoint record agree. Keep the OEM reference in the compatibility document and the HT part number on the packing list. Labels and carton groups can be arranged by rack or port plan so installers need not identify modules by appearance. For this model, the principal parameters are data rate 850Gbps (8x 106.25Gbps), wavelength 1271nm, 1291nm, 1311nm and 1331nm, rated reach 2km.
Juniper Networks Compatibility and Factory Testing
The module is checked for host recognition as QDD-2X400G-FR4-P, link establishment and diagnostic reporting. Physical cage fit alone is not treated as evidence of compatibility. Equipment model, hardware revision and software release can be reviewed before dispatch where platform behavior is uncertain.
Applications and Optical Link Design
Use this module for equipment interconnection over the specified single-mode fiber plant, including enterprise backbone, campus, metro or data-center interconnect links according to its rated distance. Confirm that both ends use the same optical standard and wavelength plan, and allow for connector, splice and patch-panel loss within the stated power budget.
Before deployment, check the host port type, supported data rate and firmware requirements. The 800G interface configuration must match the remote equipment; sharing a QSFP-DD housing alone does not make two transceiver types interoperable.
Before commissioning, measure the complete single-mode channel against the stated budget for 2km. Inspect every Dual Duplex LC/UPC connection and record diagnostic power where supported. Both ends must agree on rate, wavelength and optical standard.
Optical Acceptance, Diagnostics and Handling
For this model, the specified transmit-power range is -3.2~4.4dBm; the stated optical power budget is 4dB. A sound acceptance record includes link state, diagnostic temperature, supply voltage and transmit or receive levels where the host exposes them. Compare the readings with the stated ranges rather than treating any received light as proof of adequate margin. Persistent alarms or borderline values should trigger an end-face and complete-channel inspection. Before every insertion, keep dust caps in place until the patch lead is ready, avoid touching the optical end face and use an appropriate inspection and cleaning procedure. Do not look into an active optical interface.
Frequently Asked Questions
Is this an original Juniper Networks transceiver?
No. It is an HT-manufactured compatible alternative for equipment that specifies QDD-2X400G-FR4-P, not an original Juniper Networks-branded module.
Which fiber and connector are required?
Use Dual Duplex LC/UPC with SMF. The specified maximum reach is 2km, subject to fiber quality and total link loss.
Can it be mixed with another wavelength or reach version?
Only when the two ends share the same optical standard, wavelength plan and supported data rate. Check the exact part numbers and link budget rather than relying only on the module form factor.
Ordering Information
Use QDD-2X400G-FR4-P as the compatibility cross-reference and QDD-2FR4-800G as the HT ordering identity. Keep other reaches or wavelength directions on separate order lines. Neutral labels, customer packaging and project-specific compatibility review are available on request.
Shipping and Lead Time
Standard configurations normally ship within one to three working days, with production lead times confirmed for larger quantities. International courier, air freight and sea freight are available; customer courier accounts and nominated forwarders are accepted.
Quality Assurance and Packaging
Before packing, the module receives interface inspection, identification and link checks. Protective packaging avoids pressure on the connector and latch. Customer references, rack groups and project packing lists can be added for volume orders.
