QSFP-DD to 8x 50G SFP56-400G-AOC-50M164FT 400G QSFP-DD 8 x 50G PAM4 to 8 x 50G SFP56 25G NRZ Active Optical Breakout Cable, 50m (164ft)
The assembly listed here is the 50m (164ft) member of the QSFP-DD to 8x 50G SFP56-400G-AOC-50M164FT product family for Generic equipment. It provides 400G AOC connectivity through QSFP-DD to 8x 50G SFP56. Project teams can use the detailed table, related references and documentation-oriented packing information to keep each delivered cable aligned with its planned endpoints.
OEM Part Number: QSFP-DD to 8x 50G SFP56-400G-AOC-50M164FTHT Part Number: QSFP-DD to 8x 50G SFP56-400G-AOC-50M164FT
Product Highlights
- HT-manufactured AOC assembly in 50m (164ft)
- 400G connectivity at 425Gbps (8x 53.125GGbps)
- Interface configuration: QSFP-DD to 8x 50G SFP56
- Fixed length and part number: 50m (164ft), QSFP-DD to 8x 50G SFP56-400G-AOC-50M164FT
- Cable construction: OM3
- Maximum power consumption: 10W (QSFP-DD End) 3W (SFP56 Per End)
- Minimum bend radius: 30mm
Specifications
| HT Part Number | QSFP-DD to 8x 50G SFP56-400G-AOC-50M164FT |
|---|---|
| Manufacturer | HT |
| Form Factor | QSFP-DD to 8x 50G SFP56 |
| Max. Data Rate | 425Gbps (8x 53.125GGbps) |
| Cable Length | 50m |
| Cable Type | OM3 |
| Minimum Bend Radius | 30mm |
| Max. Power Consumption | 10W (QSFP-DD End) 3W (SFP56 Per End) |
| Transmitter Type | VSCEL |
| Receiver Type | PIN |
| Modulation Format | PAM4 |
| Wavelength | 850nm |
| Jacket Material | OFNP |
| BER | 2.4E-4 |
| Inbuilt FEC | No |
| Operating Temperature Range | 0 to 70°C (32 to 158°F) |
| Protocols | QSFP-DD MSA, SFP56 MSA, IEEE 802.3cd |
Signal and Lane Configuration
The listed modulation format is PAM4. Both host interfaces must be configured for the same aggregate rate and lane arrangement. A connector that fits mechanically does not by itself guarantee that the remote port supports this encoding or breakout mode.
Integrated Optical Assembly
The optical engines and fiber are permanently integrated into this AOC. There are no detachable optical modules to clean or exchange. Handle the complete assembly by its connector housings and cable, and keep both ends matched to the same interface specification.
Length Selection and Installation Planning
For this 50m (164ft) version, prepare the destination pathway before connecting either end. A longer assembly can cross separated equipment positions, but its weight and service slack must remain supported without blocking airflow. Handle the integrated optical cable and both optical engines as one factory-terminated product and never pull a connector into position by the cable. Within this family, QSFP-DD to 8x 50G SFP56-400G-AOC-30M98FT is shorter at 30m (98ft), while QSFP-DD to 8x 50G SFP56-400G-AOC-70M230FT is the next longer choice at 70m (230ft); comparing those two boundaries helps avoid both tension and unnecessary slack.
Position Within the Length Range
QSFP-DD to 8x 50G SFP56-400G-AOC-50M164FT occupies the middle of this family between QSFP-DD to 8x 50G SFP56-400G-AOC-30M98FT at 30m (98ft) and QSFP-DD to 8x 50G SFP56-400G-AOC-70M230FT at 70m (230ft). It adds 20m over the shorter option for extra routing clearance, while the next longer version adds another 20m. Measure the managed path and choose this version when its reach is sufficient without creating the slack associated with the longer assembly.
Project Documentation and Cable Identification
Large deployments are easier to audit when the order code, physical length and endpoint record agree. Keep the OEM reference in the compatibility document and use the HT part number on the packing list. Where several lengths arrive together, labels and carton groups can be arranged by rack or port plan so installers do not have to identify cables by appearance alone. For this assembly, the minimum bend radius is 30mm; the stated power consumption is 10W (QSFP-DD End) 3W (SFP56 Per End); the jacket material is OFNP.
Power and Thermal Planning
The rated power consumption is 10W (QSFP-DD End) 3W (SFP56 Per End). Include this load in the host-port power and thermal budget, especially in densely populated switches. Maintain front-panel clearance and do not bundle the cable so tightly that it obstructs airflow around the connectors.
Cable Construction and Routing
This assembly uses OFNP jacket, minimum bend radius 30mm. These mechanical characteristics affect how the cable should be dressed behind the equipment. Avoid sharp edges, excessive ties and repeated tight bends close to the connector boots.
Network and Protocol Considerations
The intended application is determined by the host interface and protocol support. Listed interface and protocol references include QSFP-DD MSA, SFP56 MSA, IEEE 802.3cd. Confirm that the host firmware and port configuration support the same operating mode.
Breakout Port Mapping
The QSFP-DD to 8x 50G SFP56 configuration divides the high-speed interface into multiple lower-speed connections. Verify the upstream lane assignment, downstream port speeds and breakout setting on the host before connecting the assembly. Each branch must attach to the correct remote interface.
Generic Compatibility and Factory Testing
Factory verification links the compatibility identity to the exact physical assembly described on this page. Identification, connector condition and live link behavior are checked before packing. Customers can submit equipment and firmware details with the project documentation for a more specific pre-order compatibility review. Where supported by the host, receive activity and diagnostic indications are reviewed together with the established link.
Frequently Asked Questions
Is this an original equipment manufacturer cable?
No. It is manufactured by HT under our own manufacturer identity.
What details assist a compatibility review?
Provide the equipment manufacturer, model, port type, hardware revision and software release, together with the OEM reference, required length and quantity.
How should an unused assembly be stored?
Protect both connector ends, keep the cable in a loose bend-safe coil and retain its part-number label so the length and compatibility identity remain traceable.
Can different brands be connected with the same assembly?
Only where both hosts explicitly support the complete interface and compatibility arrangement. Document each end and select the appropriate brand-specific product when required.
Ordering Information
Use the listed HT part number for ordering and retain the OEM reference as the host-compatibility cross-reference. Send quantities by length, along with any rack-based packing or label instructions. If the project has mixed equipment, include the host model for each group rather than relying only on the aggregate cable rate. Quantity and any labeling instructions should be attached specifically to QSFP-DD to 8x 50G SFP56-400G-AOC-50M164FT.
Shipping and Lead Time
Available stock is generally dispatched within one to three working days after order confirmation, with production lead times advised for larger quantities. Delivery can be arranged by courier, air freight or sea freight, and goods may instead be handed to an appointed forwarder or shipped on the customer’s courier account.
Quality Assurance and Packaging
Inspection and link testing are completed before the cable enters its protective packaging. Project orders can be packed and labelled by length, rack or customer reference, with packing documentation that makes received quantities straightforward to reconcile against the installation schedule. Volume orders can include customer references on the labels and carton list.
