OTN QSFP-ELR4-100GM Compatible 100G QSFP28 LR4 Transceiver Module
The QSFP-ELR4-100GM compatible module serves equipment requiring a 100G QSFP28 interface with 1310nm optics and a 20km rating. Connection is through Duplex LC/UPC. Product data, application guidance and factory verification are presented together to support project teams keep OEM references, delivery records and port schedules aligned.
OEM Part Number: QSFP-ELR4-100GMHT Part Number: QSFP-ELR4-100GM
Product Highlights
- Compatible alternative to OTN QSFP-ELR4-100GM
- 100G connectivity at Dual Rate 103.1Gbps and 112Gbps
- Optical wavelength: 1310nm
- Specified reach: 20km
- Duplex LC/UPC / SMF interface
- Digital diagnostic monitoring: Supported
- Operating temperature: 0 to 70°C (32 to 158°F)
Specifications
| HT Part Number | QSFP-ELR4-100GM |
|---|---|
| Manufacturer | HT |
| Form Factor | QSFP28 |
| Max. Data Rate | Dual Rate 103.1Gbps and 112Gbps |
| Wavelength | 1310nm |
| Max. Cable Distance | 20km |
| Connector | Duplex LC/UPC |
| Media | SMF |
| Transmitter Type | EML |
| Receiver Type | PIN |
| TX Power | 100G: -1.0~4.5dBm 112G: 0~4dBm |
| Minimum Receiver Power | 100G: <-9.5dBm 112G: <-9.0dBm |
| Power Budget | 100G: 8.5dB112G: 9dB |
| Receiver Overload | 100G: 4.5dBm112G: 4dBm |
| Max. Power Consumption | 3.5W |
| Extinction Ratio | >4dB |
| DDM/DOM | Supported |
| Commercial Temperature Range | 0 to 70°C (32 to 158°F) |
| Modulation (Electrical) | 4x 25G-NRZ |
| Modulation (Optical) | 4x 25G-NRZ |
| CDR (Clock and Data Recovery) | TX & RX Built-in CDR |
| Bit Error Ratio (BER) | 1.00E-12 |
| Packaging Technology | BOX Packaging |
| Inbuilt FEC | No |
| Protocols | QSFP28 MSA, SFF-8636，IEEE 802.3bm，CAUI-4 |
Project Documentation and Traceability
Large deployments are easier to audit when the order code, optical standard and endpoint record agree. Keep the OEM reference in the compatibility document and the HT part number on the packing list. Labels and carton groups can be arranged by rack or port plan so installers need not identify modules by appearance. For this model, the principal parameters are data rate Dual Rate 103.1Gbps and 112Gbps, wavelength 1310nm, rated reach 20km.
OTN Compatibility and Factory Testing
Factory verification starts with the expected QSFP-ELR4-100GM identity and finishes with an operating host link. EEPROM data, diagnostic visibility and the stated optical parameters are assessed together. Equipment model, hardware revision and software release can be reviewed before dispatch where platform behavior is uncertain.
Applications and Optical Link Design
Use this module for equipment interconnection over the specified single-mode fiber plant, including enterprise backbone, campus, metro or data-center interconnect links according to its rated distance. Confirm that both ends use the same optical standard and wavelength plan, and allow for connector, splice and patch-panel loss within the stated power budget.
Before deployment, check the host port type, supported data rate and firmware requirements. The 100G interface configuration must match the remote equipment; sharing a QSFP28 housing alone does not make two transceiver types interoperable.
Before commissioning, measure the complete single-mode channel against the stated budget for 20km. Inspect every Duplex LC/UPC connection and record diagnostic power where supported. Both ends must agree on rate, wavelength and optical standard.
Optical Acceptance, Diagnostics and Handling
For this model, the specified transmit-power range is 100G: -1.0~4.5dBm 112G: 0~4dBm; the stated optical power budget is 100G: 8.5dB112G: 9dB. Digital diagnostics make later maintenance easier when baseline values are captured at installation. Save the initial readings with the port and OEM reference, then investigate meaningful changes rather than reacting to a single transient value. Diagnostic support depends on the host as well as the module, so unavailable fields should be confirmed with the platform documentation. Diagnostic monitoring is listed as Supported. Before every insertion, keep dust caps in place until the patch lead is ready, avoid touching the optical end face and use an appropriate inspection and cleaning procedure. Do not look into an active optical interface.
Frequently Asked Questions
Is this an original OTN transceiver?
No. It is an HT-manufactured compatible alternative for equipment that specifies QSFP-ELR4-100GM, not an original OTN-branded module.
Which fiber and connector are required?
Use Duplex LC/UPC with SMF. The specified maximum reach is 20km, subject to fiber quality and total link loss.
Can it be mixed with another wavelength or reach version?
Only when the two ends share the same optical standard, wavelength plan and supported data rate. Check the exact part numbers and link budget rather than relying only on the module form factor.
Ordering Information
Quote HT part number QSFP-ELR4-100GM together with OEM reference QSFP-ELR4-100GM and quantity. Add the host model and software release when pre-order verification is required. Neutral labels, customer packaging and project-specific compatibility review are available on request.
Shipping and Lead Time
Standard configurations normally ship within one to three working days, with production lead times confirmed for larger quantities. International courier, air freight and sea freight are available; customer courier accounts and nominated forwarders are accepted.
Quality Assurance and Packaging
Before packing, the module receives interface inspection, identification and link checks. Protective packaging avoids pressure on the connector and latch. Customer references, rack groups and project packing lists can be added for volume orders.
