H3C QSFPDD-800G-VR8-MM850-DMPO Compatible 800G QSFP-DD SR8 Transceiver Module
The QSFPDD-800G-VR8-MM850-DMPO compatible module serves equipment requiring a 800G QSFP-DD interface with 850nm optics and a 30m on OM3 / 50m on OM4 rating. Connection is through MTP/MPO-16 APC. Product data, application guidance and factory verification are presented together to support project teams keep OEM references, delivery records and port schedules aligned.
OEM Part Number: QSFPDD-800G-VR8-MM850-DMPOHT Part Number: QDD-SR8-800G
Product Highlights
- Compatible alternative to H3C QSFPDD-800G-VR8-MM850-DMPO
- 800G connectivity at 850Gbps (8x 106.25Gbps)
- Optical wavelength: 850nm
- Specified reach: 30m on OM3 / 50m on OM4
- MTP/MPO-16 APC / MMF interface
- Factory compatibility verification and optical performance testing before shipment
Specifications
| H3C Compatible | QSFPDD-800G-VR8-MM850-DMPO |
|---|---|
| Manufacturer | HT |
| HT Part Number | QDD-SR8-800G |
| Form Factor | QSFP-DD |
| Max Data Rate | 850Gbps (8x 106.25Gbps) |
| Wavelength | 850nm |
| Max Cable Distance | 30m@OM3/50m@OM4 |
| Connector | MTP/MPO-16 APC |
| Cable Type | MMF |
| Transmitter Type | VCSEL |
| Receiver Type | PIN |
| TX Power | -4.6-4dBm |
| Minimum Receiver Power | -6.4dBm |
| Power Budget | 1.8dB |
| Receiver Overload | 4dBm |
| Max. Power Consumption | 16W |
| Extinction Ratio | ＞2.5dB |
| Modulation (Electrical) | 8x 100G-PAM4 |
| Modulation (Optical) | 8x 100G-PAM4 |
| Packaging Technology | COB (Chip on Board) Packaging |
| Modulation Format | PAM4 |
| CDR (Clock and Data Recovery) | TX and RX Built-in DSP |
| Inbuilt FEC | No |
| Protocols | QSFP-DD MSA Hardware Rev 7.0, CMIS Rev 5.0, IEEE 802.3df-2024, IEEE 802.3df-2024 |
Project Documentation and Traceability
Large deployments are easier to audit when the order code, optical standard and endpoint record agree. Keep the OEM reference in the compatibility document and the HT part number on the packing list. Labels and carton groups can be arranged by rack or port plan so installers need not identify modules by appearance. For this model, the principal parameters are data rate 850Gbps (8x 106.25Gbps), wavelength 850nm, rated reach 30m on OM3 / 50m on OM4.
H3C Compatibility and Factory Testing
Compatibility testing for QSFPDD-800G-VR8-MM850-DMPO combines identification with a live link and available transmit, receive and alarm information. Connector condition is inspected separately. Equipment model, hardware revision and software release can be reviewed before dispatch where platform behavior is uncertain.
Applications and Optical Link Design
Typical deployments include switch-to-switch, switch-to-server and aggregation links inside a data hall or between adjacent equipment rooms. The MTP/MPO-16 APC interface connects to the specified multimode cabling, and the stated reach depends on fiber grade and link loss. Keep this interface on the matching multimode optical standard rather than connecting it directly to a single-mode wavelength or reach variant.
Before deployment, check the host port type, supported data rate and firmware requirements. The 800G interface configuration must match the remote equipment; sharing a QSFP-DD housing alone does not make two transceiver types interoperable.
For this multimode module, confirm fiber grade, modal bandwidth and total loss before commissioning. The 30m on OM3 / 50m on OM4 figure applies only under suitable cabling conditions. Inspect every MTP/MPO-16 APC mating point and match the remote optical standard.
Optical Acceptance, Diagnostics and Handling
For this model, the specified transmit-power range is -4.6-4dBm; the stated optical power budget is 1.8dB. During commissioning, record the host diagnostic readings after the link has stabilized and compare them with those limits. DOM values are useful operational indicators, but they do not replace calibrated optical measurements when a link is marginal. Investigate unexpected loss through connector inspection, cleaning and a channel measurement before replacing the module. Before every insertion, keep dust caps in place until the patch lead is ready, avoid touching the optical end face and use an appropriate inspection and cleaning procedure. Do not look into an active optical interface.
Frequently Asked Questions
Is this an original H3C transceiver?
No. It is an HT-manufactured compatible alternative for equipment that specifies QSFPDD-800G-VR8-MM850-DMPO, not an original H3C-branded module.
Which fiber and connector are required?
Use MTP/MPO-16 APC with MMF. The specified maximum reach is 30m on OM3 / 50m on OM4, subject to fiber quality and total link loss.
Can it be mixed with another wavelength or reach version?
Only when the two ends share the same optical standard, wavelength plan and supported data rate. Check the exact part numbers and link budget rather than relying only on the module form factor.
Ordering Information
Use QSFPDD-800G-VR8-MM850-DMPO as the compatibility cross-reference and QDD-SR8-800G as the HT ordering identity. Keep other reaches or wavelength directions on separate order lines. Neutral labels, customer packaging and project-specific compatibility review are available on request.
Shipping and Lead Time
Standard configurations normally ship within one to three working days, with production lead times confirmed for larger quantities. International courier, air freight and sea freight are available; customer courier accounts and nominated forwarders are accepted.
Quality Assurance and Packaging
Before packing, the module receives interface inspection, identification and link checks. Protective packaging avoids pressure on the connector and latch. Customer references, rack groups and project packing lists can be added for volume orders.
