HPE Aruba R0R40A Compatible 100G QSFP28 SR Transceiver Module
Built for hosts recognizing R0R40A, this HT-manufactured QSFP28 module delivers 100G transmission at 850/880/910/940nm. Its rated reach is 75m on OM3 / 100m on OM4 / 150m on OM5, with Duplex LC/UPC as the physical interface. The specifications and engineering guidance below support project teams keep OEM references, delivery records and port schedules aligned, while keeping HT manufacture separate from the OEM cross-reference.
OEM Part Number: R0R40AHT Part Number: QSFP-BIDI-100G
Product Highlights
- Compatible alternative to HPE Aruba R0R40A
- 100G connectivity at 103.1Gbps
- Optical wavelength: 850/880/910/940nm
- Specified reach: 75m on OM3 / 100m on OM4 / 150m on OM5
- Duplex LC/UPC / MMF interface
- Digital diagnostic monitoring: Supported
- Operating temperature: 0 to 70°C (32 to 158°F)
Specifications
| HPE Aruba Compatible | R0R40A |
|---|---|
| Manufacturer | HT |
| HT Part Number | QSFP-BIDI-100G |
| Form Factor | QSFP28 |
| Max. Data Rate | 103.1Gbps |
| Wavelength | 850/880/910/940nm |
| Max. Cable Distance | 75m@OM3/100m@OM4/150m@OM5 |
| Connector | Duplex LC/UPC |
| Media | MMF |
| Transmitter Type | VCSEL |
| Receiver Type | PIN |
| TX Power | -5.5~3dBm |
| Minimum Receiver Power | -9.5dBm |
| Power Budget | 4dB |
| Receiver Overload | 3.4dBm |
| Max. Power Consumption | 3.5W |
| Extinction Ratio | >2dB |
| DDM/DOM | Supported |
| Commercial Temperature Range | 0 to 70°C (32 to 158°F) |
| Modulation (Electrical) | 4x 25G-NRZ |
| Modulation (Optical) | 4x 25G-NRZ |
| CDR (Clock and Data Recovery) | TX & RX Built-in CDR |
| Packaging Technology | COB Packaging |
| Bit Error Ratio (BER) | 5E-5 |
| MTBF | 11,100,000 Hours (@40°C, 60% CL) |
| Protocols | QSFP28 MSA, SFF-8636, IEEE 802.3bm, CAUI-4 |
Project Documentation and Traceability
Large deployments are easier to audit when the order code, optical standard and endpoint record agree. Keep the OEM reference in the compatibility document and the HT part number on the packing list. Labels and carton groups can be arranged by rack or port plan so installers need not identify modules by appearance. For this model, the principal parameters are data rate 103.1Gbps, wavelength 850/880/910/940nm, rated reach 75m on OM3 / 100m on OM4 / 150m on OM5.
HPE Aruba Compatibility and Factory Testing
Compatibility testing for R0R40A combines identification with a live link and available transmit, receive and alarm information. Connector condition is inspected separately. Equipment model, hardware revision and software release can be reviewed before dispatch where platform behavior is uncertain.
Applications and Optical Link Design
Typical deployments include switch-to-switch, switch-to-server and aggregation links inside a data hall or between adjacent equipment rooms. The Duplex LC/UPC interface connects to the specified multimode cabling, and the stated reach depends on fiber grade and link loss. Keep this interface on the matching multimode optical standard rather than connecting it directly to a single-mode wavelength or reach variant.
Before deployment, check the host port type, supported data rate and firmware requirements. The 100G interface configuration must match the remote equipment; sharing a QSFP28 housing alone does not make two transceiver types interoperable.
For this multimode module, confirm fiber grade, modal bandwidth and total loss before commissioning. The 75m on OM3 / 100m on OM4 / 150m on OM5 figure applies only under suitable cabling conditions. Inspect every Duplex LC/UPC mating point and match the remote optical standard.
Optical Acceptance, Diagnostics and Handling
For this model, the specified transmit-power range is -5.5~3dBm; the stated optical power budget is 4dB. During commissioning, record the host diagnostic readings after the link has stabilized and compare them with those limits. DOM values are useful operational indicators, but they do not replace calibrated optical measurements when a link is marginal. Investigate unexpected loss through connector inspection, cleaning and a channel measurement before replacing the module. Diagnostic monitoring is listed as Supported. Before every insertion, keep dust caps in place until the patch lead is ready, avoid touching the optical end face and use an appropriate inspection and cleaning procedure. Do not look into an active optical interface.
Frequently Asked Questions
Is this an original HPE Aruba transceiver?
No. It is an HT-manufactured compatible alternative for equipment that specifies R0R40A, not an original HPE Aruba-branded module.
Which fiber and connector are required?
Use Duplex LC/UPC with MMF. The specified maximum reach is 75m on OM3 / 100m on OM4 / 150m on OM5, subject to fiber quality and total link loss.
Can it be mixed with another wavelength or reach version?
Only when the two ends share the same optical standard, wavelength plan and supported data rate. Check the exact part numbers and link budget rather than relying only on the module form factor.
Ordering Information
When ordering, specify R0R40A, QSFP-BIDI-100G, quantity and intended host platform. Project labels can repeat these details for receiving and asset records. Neutral labels, customer packaging and project-specific compatibility review are available on request.
Shipping and Lead Time
Standard configurations normally ship within one to three working days, with production lead times confirmed for larger quantities. International courier, air freight and sea freight are available; customer courier accounts and nominated forwarders are accepted.
Quality Assurance and Packaging
Quality control covers the optical or electrical interface, host identification and operating link. The verified unit is then individually protected and cartoned. Customer references, rack groups and project packing lists can be added for volume orders.
