SFP-DD to SFP-DD-100G-AOC-2M7FT 100G SFP-DD 2 x 50G PAM4 Active Optical Cable, 2m (7ft)
For project documentation, Generic SFP-DD to SFP-DD-100G-AOC-2M7FT and this cable’s physical length should be recorded together. The product described here is a 2m (7ft) AOC assembly for 100G links, using SFP-DD to SFP-DD. Its OEM cross-reference, HT part number, specification table and packing options support traceable ordering and installation records.
OEM Part Number: SFP-DD to SFP-DD-100G-AOC-2M7FTHT Part Number: SFP-DD to SFP-DD-100G-AOC-2M7FT
Product Highlights
- HT-manufactured AOC assembly in 2m (7ft)
- 100G connectivity at 100Gbps
- Interface configuration: SFP-DD to SFP-DD
- Fixed length and part number: 2m (7ft), SFP-DD to SFP-DD-100G-AOC-2M7FT
- Cable construction: OM4
- Maximum power consumption: ≤3.5W
- Minimum bend radius: 60mm
Specifications
| HT Part Number | SFP-DD to SFP-DD-100G-AOC-2M7FT |
|---|---|
| Manufacturer | HT |
| Connector Type | SFP-DD to SFP-DD |
| Max Data Rate | 100Gbps |
| Cable Length | 2m (7ft) |
| Cable Type | OM4 |
| Wavelength | 850nm |
| Minimum Bend Radius | 60mm |
| Transmitter Type | VSCEL |
| Receiver Type | PIN |
| Power Consumption | ≤3.5W |
| Power supply | 3.5V |
| CDR (Clock and Data Recovery) | TX & RX Built-in CDR |
| Modulation Format | 2x 50G-PAM4 to 2x 50G-PAM4 |
| DDM/DOM | Supported |
| Commercial Temperature | 0 to 70°C (32 to 158°F) |
| Protocols | SFP-DD MSA, SFP-DD MIS |
Signal and Lane Configuration
The listed modulation format is 2x 50G-PAM4 to 2x 50G-PAM4. Both host interfaces must be configured for the same aggregate rate and lane arrangement. A connector that fits mechanically does not by itself guarantee that the remote port supports this encoding or breakout mode.
Integrated Optical Assembly
The optical engines and fiber are permanently integrated into this AOC. There are no detachable optical modules to clean or exchange. Handle the complete assembly by its connector housings and cable, and keep both ends matched to the same interface specification.
Length Selection and Installation Planning
SFP-DD to SFP-DD-100G-AOC-2M7FT provides 2m (7ft) for connections between separated rack units or nearby equipment positions. Plan the route around cable managers and power cords, keeping the assembly free from connector strain while avoiding a large obstruction in the airflow path.
Position Within the Length Range
SFP-DD to SFP-DD-100G-AOC-2M7FT occupies the middle of this family between SFP-DD to SFP-DD-100G-AOC-1M3FT at 1m (3ft) and SFP-DD to SFP-DD-100G-AOC-3M10FT at 3m (10ft). It adds 1m over the shorter option for extra routing clearance, while the next longer version adds another 1m. Measure the managed path and choose this version when its reach is sufficient without creating the slack associated with the longer assembly.
Project Documentation and Cable Identification
Large deployments are easier to audit when the order code, physical length and endpoint record agree. Keep the OEM reference in the compatibility document and use the HT part number on the packing list. Where several lengths arrive together, labels and carton groups can be arranged by rack or port plan so installers do not have to identify cables by appearance alone. For this assembly, the minimum bend radius is 60mm; the stated power consumption is ≤3.5W.
Power and Thermal Planning
The rated power consumption is ≤3.5W. Include this load in the host-port power and thermal budget, especially in densely populated switches. Maintain front-panel clearance and do not bundle the cable so tightly that it obstructs airflow around the connectors.
Cable Construction and Routing
This assembly uses minimum bend radius 60mm. These mechanical characteristics affect how the cable should be dressed behind the equipment. Avoid sharp edges, excessive ties and repeated tight bends close to the connector boots.
Network and Protocol Considerations
The intended application is determined by the host interface and protocol support. Listed interface and protocol references include SFP-DD MSA, SFP-DD MIS. Confirm that the host firmware and port configuration support the same operating mode.
Generic Compatibility and Factory Testing
Factory verification links the compatibility identity to the exact physical assembly described on this page. Identification, connector condition and live link behavior are checked before packing. Customers can submit equipment and firmware details with the project documentation for a more specific pre-order compatibility review. The check includes receive activity and diagnostic indications, followed by a final inspection of both ends.
Frequently Asked Questions
Is this an original equipment manufacturer cable?
No. It is manufactured by HT under our own manufacturer identity.
Can different brands be connected with the same assembly?
Only where both hosts explicitly support the complete interface and compatibility arrangement. Document each end and select the appropriate brand-specific product when required.
Does this order code cover multiple lengths?
No. SFP-DD to SFP-DD-100G-AOC-2M7FT refers here to 2m (7ft). Every other verified length has a separate part number and page in the length list.
Are separate transceivers or patch leads required?
No. This is one complete direct-attach assembly. The ends are not detachable modules and should not be separated from the cable.
Ordering Information
Use the listed HT part number for ordering and retain the OEM reference as the host-compatibility cross-reference. Send quantities by length, along with any rack-based packing or label instructions. If the project has mixed equipment, include the host model for each group rather than relying only on the aggregate cable rate. Keep SFP-DD to SFP-DD-100G-AOC-2M7FT associated with 2m (7ft) throughout the order and receiving record.
Shipping and Lead Time
Standard configurations normally ship within one to three working days, while production quantities are confirmed with the order. Delivery can be arranged by courier, air freight or sea freight, and goods may instead be handed to an appointed forwarder or shipped on the customer’s courier account.
Quality Assurance and Packaging
Inspection and link testing are completed before the cable enters its protective packaging. Project orders can be packed and labelled by length, rack or customer reference, with packing documentation that makes received quantities straightforward to reconcile against the installation schedule. Neutral packaging and customer-specific packing documentation are available on request.
