H3C SFP-GE-SX-MM850-A Compatible 1G SFP Transceiver Module
Built for hosts recognizing SFP-GE-SX-MM850-A, this HT-manufactured SFP module delivers 1G transmission at 850nm. Its rated reach is 550m on 50 / 125µm OM2 MMF275m on 62.5 / 125µm OM1 MMF220m on 62.5 / 125µm FDDI MMF, with Duplex LC as the physical interface. The specifications and engineering guidance below support project teams keep OEM references, delivery records and port schedules aligned, while keeping HT manufacture separate from the OEM cross-reference.
OEM Part Number: SFP-GE-SX-MM850-AHT Part Number: SFP-GE-SX-MM850-A
Product Highlights
- Compatible alternative to H3C SFP-GE-SX-MM850-A
- 1G connectivity at 1.25Gbps
- Optical wavelength: 850nm
- Specified reach: 550m on 50 / 125µm OM2 MMF275m on 62.5 / 125µm OM1 MMF220m on 62.5 / 125µm FDDI MMF
- Duplex LC / MMF interface
- Digital diagnostic monitoring: Supported
- Operating temperature: 0 to 70°C (23 to 158°F)
Specifications
| H3C Compatible | SFP-GE-SX-MM850-A |
|---|---|
| Manufacturer | HT |
| HT Part Number | SFP-GE-SX-MM850-A |
| Form Factor | SFP |
| Max. Data Rate | 1.25Gbps |
| Wavelength | 850nm |
| Max. Cable Distance | 550m@50/125µm OM2 MMF275m@62.5/125µm OM1 MMF220m@62.5/125µm FDDI MMF |
| Connector | Duplex LC |
| Media | MMF |
| Transmitter Type | VCSEL |
| Receiver Type | PIN |
| DDM/DOM | Supported |
| Commercial Temperature Range | 0 to 70°C (23 to 158°F) |
| TX Power | -9.5~-3dBm |
| Receiver Sensitivity | < -17dBm |
| Typical Power Consumption | ≤0.8W |
| Receiver Overload | -3dBm |
| Bit Error Ratio (BER) | 1E-12 |
| Extinction Ratio | >9dB |
| EMC (Electro Magnetic Compatibility) | Supported |
| MTBF (SX) | 2,457,002 Hours |
| Protocols | IEEE 802.3z, SFF-8472, SFP MSA (INF-8074i) Compliant |
Project Documentation and Traceability
Large deployments are easier to audit when the order code, optical standard and endpoint record agree. Keep the OEM reference in the compatibility document and the HT part number on the packing list. Labels and carton groups can be arranged by rack or port plan so installers need not identify modules by appearance. For this model, the principal parameters are data rate 1.25Gbps, wavelength 850nm, rated reach 550m on 50 / 125µm OM2 MMF275m on 62.5 / 125µm OM1 MMF220m on 62.5 / 125µm FDDI MMF.
H3C Compatibility and Factory Testing
Factory verification starts with the expected SFP-GE-SX-MM850-A identity and finishes with an operating host link. EEPROM data, diagnostic visibility and the stated optical parameters are assessed together. Equipment model, hardware revision and software release can be reviewed before dispatch where platform behavior is uncertain.
Applications and Optical Link Design
Typical deployments include switch-to-switch, switch-to-server and aggregation links inside a data hall or between adjacent equipment rooms. The Duplex LC interface connects to the specified multimode cabling, and the stated reach depends on fiber grade and link loss. Keep this interface on the matching multimode optical standard rather than connecting it directly to a single-mode wavelength or reach variant.
Before deployment, check the host port type, supported data rate and firmware requirements. The 1G interface configuration must match the remote equipment; sharing a SFP housing alone does not make two transceiver types interoperable.
The multimode channel should use the fiber grade associated with the stated 550m on 50 / 125µm OM2 MMF275m on 62.5 / 125µm OM1 MMF220m on 62.5 / 125µm FDDI MMF reach. Keep the Duplex LC end faces clean and avoid tight bends. Different multimode standards are not interchangeable merely because they share a connector.
Optical Acceptance, Diagnostics and Handling
For this model, the specified transmit-power range is -9.5~-3dBm; receiver sensitivity is < -17dBm. A sound acceptance record includes link state, diagnostic temperature, supply voltage and transmit or receive levels where the host exposes them. Compare the readings with the stated ranges rather than treating any received light as proof of adequate margin. Persistent alarms or borderline values should trigger an end-face and complete-channel inspection. Diagnostic monitoring is listed as Supported. Before every insertion, keep dust caps in place until the patch lead is ready, avoid touching the optical end face and use an appropriate inspection and cleaning procedure. Do not look into an active optical interface.
Frequently Asked Questions
Is this an original H3C transceiver?
No. It is an HT-manufactured compatible alternative for equipment that specifies SFP-GE-SX-MM850-A, not an original H3C-branded module.
Which fiber and connector are required?
Use Duplex LC with MMF. The specified maximum reach is 550m on 50 / 125µm OM2 MMF275m on 62.5 / 125µm OM1 MMF220m on 62.5 / 125µm FDDI MMF, subject to fiber quality and total link loss.
Can it be mixed with another wavelength or reach version?
Only when the two ends share the same optical standard, wavelength plan and supported data rate. Check the exact part numbers and link budget rather than relying only on the module form factor.
Ordering Information
Use SFP-GE-SX-MM850-A as the compatibility cross-reference and SFP-GE-SX-MM850-A as the HT ordering identity. Keep other reaches or wavelength directions on separate order lines. Neutral labels, customer packaging and project-specific compatibility review are available on request.
Shipping and Lead Time
Standard configurations normally ship within one to three working days, with production lead times confirmed for larger quantities. International courier, air freight and sea freight are available; customer courier accounts and nominated forwarders are accepted.
Quality Assurance and Packaging
Each SFP-GE-SX-MM850-A compatible module is inspected, powered up and functionally checked before protective packing. Dust caps and individual trays shield the interface during transport. Customer references, rack groups and project packing lists can be added for volume orders.
