SFP28-25G-AOC-20M66FT SFP28 Industrial Active Optical Cable, 20m (66ft)
The assembly listed here is the 20m (66ft) member of the SFP28-25G-AOC-20M66FT product family for Generic equipment. It provides 25G AOC connectivity through SFP28. Project teams can use the detailed table, related references and documentation-oriented packing information to keep each delivered cable aligned with its planned endpoints.
OEM Part Number: SFP28-25G-AOC-20M66FTHT Part Number: SFP28-25G-AOC-20M66FT
Product Highlights
- HT-manufactured AOC assembly in 20m (66ft)
- 25G connectivity at 25.78125Gbps
- Interface configuration: SFP28
- Fixed length and part number: 20m (66ft), SFP28-25G-AOC-20M66FT
- Cable construction: OM3
- Maximum power consumption: < 1W
- Minimum bend radius: 30mm
- Operating temperature: -40 to 85°C (-40 to 185°F)
Specifications
| HT Part Number | SFP28-25G-AOC-20M66FT |
|---|---|
| Manufacturer | HT |
| Form Factor | SFP28 |
| Max Data Rate | 25.78125Gbps |
| Wavelength | 850nm |
| Cable Type | OM3 |
| Minimum Bend Radius | 30mm |
| Cable Length | 20m(66ft) |
| Power Consumption | < 1W |
| Jacket Material | OFNP |
| Industrial Temperature Range | -40 to 85°C (-40 to 185°F) |
| Protocols | SFP28 MSA，IEEE 802.3by 25GBASE-SR |
Power and Thermal Planning
The rated power consumption is < 1W. Include this load in the host-port power and thermal budget, especially in densely populated switches. Maintain front-panel clearance and do not bundle the cable so tightly that it obstructs airflow around the connectors.
Integrated Optical Assembly
The optical engines and fiber are permanently integrated into this AOC. There are no detachable optical modules to clean or exchange. Handle the complete assembly by its connector housings and cable, and keep both ends matched to the same interface specification.
Length Selection and Installation Planning
Longer assemblies require disciplined cable dressing. For SFP28-25G-AOC-20M66FT at 20m (66ft), use the intended managers rather than a diagonal route across the rack, and leave enough space to release each connector. Any service allowance should be loose and supported, with the integrated optical cable and both optical engines protected throughout the path. Within this family, SFP28-25G-AOC-15M49FT is shorter at 15m (49ft), while SFP28-25G-AOC-25M82FT is the next longer choice at 25m (82ft); comparing those two boundaries helps avoid both tension and unnecessary slack.
Position Within the Length Range
SFP28-25G-AOC-20M66FT occupies the middle of this family between SFP28-25G-AOC-15M49FT at 15m (49ft) and SFP28-25G-AOC-25M82FT at 25m (82ft). It adds 5m over the shorter option for extra routing clearance, while the next longer version adds another 5m. Measure the managed path and choose this version when its reach is sufficient without creating the slack associated with the longer assembly.
Project Documentation and Cable Identification
Large deployments are easier to audit when the order code, physical length and endpoint record agree. Keep the OEM reference in the compatibility document and use the HT part number on the packing list. Where several lengths arrive together, labels and carton groups can be arranged by rack or port plan so installers do not have to identify cables by appearance alone. For this assembly, the minimum bend radius is 30mm; the stated power consumption is < 1W; the jacket material is OFNP.
Cable Construction and Routing
This assembly uses OFNP jacket, minimum bend radius 30mm. These mechanical characteristics affect how the cable should be dressed behind the equipment. Avoid sharp edges, excessive ties and repeated tight bends close to the connector boots.
Network and Protocol Considerations
The intended application is determined by the host interface and protocol support. Listed interface and protocol references include SFP28 MSA，IEEE 802.3by 25GBASE-SR. Confirm that the host firmware and port configuration support the same operating mode.
Generic Compatibility and Factory Testing
Factory verification links the compatibility identity to the exact physical assembly described on this page. Identification, connector condition and live link behavior are checked before packing. Customers can submit equipment and firmware details with the project documentation for a more specific pre-order compatibility review. Where supported by the host, receive activity and diagnostic indications are reviewed together with the established link.
Frequently Asked Questions
Is this an original equipment manufacturer cable?
No. It is manufactured by HT under our own manufacturer identity.
Are separate transceivers or patch leads required?
No. This is one complete direct-attach assembly. The ends are not detachable modules and should not be separated from the cable.
Can excess cable be folded into a compact bundle?
No. Use a supported, bend-safe service loop and observe the listed minimum bend radius. Do not crease the cable or tighten ties around the connector boots.
Will any matching connector operate at the same speed?
Not necessarily. Both hosts must support the stated rate, identification, lane mapping and any required breakout configuration; mechanical compatibility alone is insufficient.
Ordering Information
Use the listed HT part number for ordering and retain the OEM reference as the host-compatibility cross-reference. Send quantities by length, along with any rack-based packing or label instructions. If the project has mixed equipment, include the host model for each group rather than relying only on the aggregate cable rate. This page’s fixed configuration is 20m (66ft); another length must be quoted under its corresponding part number.
Shipping and Lead Time
Available stock is generally dispatched within one to three working days after order confirmation, with production lead times advised for larger quantities. International express, air cargo and sea freight can be selected according to destination and carton volume; customer courier accounts and nominated forwarders are also accepted.
Quality Assurance and Packaging
Inspection and link testing are completed before the cable enters its protective packaging. Project orders can be packed and labelled by length, rack or customer reference, with packing documentation that makes received quantities straightforward to reconcile against the installation schedule. Neutral packaging and customer-specific packing documentation are available on request.
